Titre :

Eccentricity Optimisation of Annular Multi-Tube Storage Unit with Phase Change Material

Auteur(s) :

HARMEN, YASSER [Auteur]
Université Mohammed VI Polytechnique = Mohammed VI Polytechnic University [Ben Guerir] [UM6P]
Université Ibn Tofaïl [UIT]
Chhiti, Younes [Auteur]
Université Mohammed VI Polytechnique = Mohammed VI Polytechnic University [Ben Guerir] [UM6P]
Université Ibn Tofaïl [UIT]
El Fiti, Maryam [Auteur]
Université Mohammed VI Polytechnique = Mohammed VI Polytechnic University [Ben Guerir] [UM6P]
Université Ibn Tofaïl [UIT]
Salihi, Mustapha [Auteur]
Université Mohammed VI Polytechnique = Mohammed VI Polytechnic University [Ben Guerir] [UM6P]
Université Ibn Tofaïl [UIT]
Jama, charafeddine [Auteur]
Unité Matériaux et Transformations - UMR 8207 [UMET]

Titre de la revue :

SSRN Electronic Journal

Nom court de la revue :

SSRN Journal

Éditeur :

Elsevier BV

Date de publication :

2022-09-16

ISSN :

1556-5068

Mot(s)-clé(s) en anglais :

Thermal energy storage
Phase change material
Computational fluid dynamics
Heat transfer enhancement
Eccentricity

Discipline(s) HAL :

Chimie/Matériaux
Chimie/Polymères

Résumé en anglais : [en]

Thermal energy storage (TES) with phase change materials (PCM) can improve energy efficiency by reducing energy availability and demand mismatch. However, despite the potential of this technology, the low thermal conductivity ...
Lire la suite >Thermal energy storage (TES) with phase change materials (PCM) can improve energy efficiency by reducing energy availability and demand mismatch. However, despite the potential of this technology, the low thermal conductivity of PCM slows down the storage cycle and limits its commercialisation. The literature has proposed many solutions to improve heat transfer, such as fins, encapsulation, or metal foam inserts, which are too expensive and complicated. This study focuses on an inexpensive and practical solution, eccentricity of shell and tube heat exchanger (STHE). The eccentricity of four horizontal STHE with 1, 2, 3, and 4 tubes is studied. The PCM melting and solidifying characteristics with varied eccentricities are accurately predicted by the enthalpy double porosities model. Results reveal that the eccentric charge performance is better than the concentric arrangement of the tube. An optimal eccentricity of the charge cycle exists that depends on the tube. The optimal eccentricities of the single and multi-tube systems are 6 and 10. The total melting time of optimal eccentricity for the four-tube, three-tube, two-tube, and single-tube is optimised by 63%,63%, 60% and 54% compared to the concentric cases, respectively. The optimal eccentricity of the single-tube case has the shortest melting time, which increases linearly with the Rayleigh number. The concentric cases consistently exhibit the best performance and shortest solidification time as the Rayleigh number increases. The total solidification time of the single-tube case is reduced by 56%, 52% and 49% compared to the four-tube, three-tube and two-tube, respectively. The multiphysical mechanisms of the charge and discharge cycles are discussed. Special attention is paid to understanding the melting and solidification behaviour.Lire moins >

Langue :

Anglais

Audience :

Internationale

Vulgarisation :

Non

Établissement(s) :

Université de Lille
CNRS
INRAE
ENSCL

Collections :

• Unité Matériaux et Transformations (UMET) - UMR 8207

Équipe(s) de recherche :

Procédés de Recyclage et de Fonctionnalisation (PReF)

Date de dépôt :

2022-09-20T15:06:39Z
2022-09-23T07:38:30Z